The WMI Provider Host error eats up a lot of your computer’s processing power. WMI Provider Host High CPU (WmiPrvSE.exe) Error WMI Provider Host High CPU (WmiPrvSE.exe) Error WMI Provider Host High CPU (WmiPrvSE.exe) Error WMI Provider Host High CPU (WmiPrvSE.exe) Error WMI Provider Ho
As a result, if there is a problem with WMI Provider Host, it dominates your computer’s CPU and renders many of the PC’s capabilities ineffective. After updating your PC from Windows 7 to Windows 10, you may notice this behaviour or problem.
WMI Provider Host (WMI Provider Host) (WmiPrvSE.exe) On Windows 10, there is a lot of CPU usage.

Error
The WMI Provider Host High CPU Usage problem, on the other hand, can be readily resolved by following the steps outlined in this article.
Method 1: Restarting the Windows Management Instrumentation Service
The problem is almost always with your computer’s WMI Provider Host Service, which may be taking up too much space and producing issues. As a result, you might want to try restarting your WMI Service:
Step 1- Turn on your computer and hit the Windows + R key combination to bring up the Run dialogue box.
Step 2 – In the Run dialogue box, type services.msc and press the Enter key.
Step 3 – Next, press the W key to open the services console window and look for the Windows Management Instrumentation Service.
Step 4 – After you’ve found the WMI service, right-click it and select the restart option to restart it. You can also choose to discontinue using the service, although I would not recommend it.
Method 2 – Restart Other Associated Services DNS Probe Finished Bad Config
After you’ve finished restarting the WMI service, go ahead and restart any other connected services by following these steps:
Step 1- Turn on your computer and go to the Command Prompt (Admin) menu.
Step 2 – Next, type the following commands one by one in the command prompt window, pressing enter after each command:
wscsvc net stop iphlpsvc net stop iphlpsvc net stop iphlpsvc net stop iphlpsvc net start wscsvc net start iphlpsvc Winmgmt
Step 3 – Once you’ve completed this, restart your computer to see if the problem has been resolved.
Method 3: Perform a Clean Boot to Locate a Malicious Application
Because high CPU utilisation by WMI Provider Host might sometimes be caused by a specific application, you can conduct a clean boot and then isolate the problematic application. Follow the steps below to try this method:
Step 1 – Create an Administrator account on your computer.
Step 2 – Press the Windows + R key combination to bring up the Run Dialogue Box.
Step 3 – In the Run dialogue box, type “msconfig” and press the Enter key.
Step 4 – In the next window that appears, pick Services, and then uncheck the “Hide all Microsoft Services” button in the left corner bottom.
Step 5 – Press OK after selecting the Disable All option.
Step 6 – Click the “Open Task Manager” option on the “Startup” tab.
Step 7 – In the Task Manager window, click the Startup button, then choose the applications that have Enabled written next to them and disable them all.
Step 8 – Repeat steps 1–8 for all of the specified applications, then restart your computer.
Step 9 – Now that your machine is in Clean boot mode, check to see if your problem has been resolved.
Step 10 – If the mistake has been resolved, it was most likely triggered by a third-party programme or service.
Step 11 – Then, one by one, enable the services; if the high CPU utilisation occurs again, disable those services.
Step 12 – Finally, reinstall the programme or service that created the problem.
Method 4: Use Event Viewer to locate the process and uninstall it.
This can be accomplished by following the steps below:
Step 1 – First and foremost, you must launch the Event Viewer, which can be done in one of two ways depending on your computer’s operating system:
1.You can find Event Viewer under the Start Menu if you’re using Windows 7 or an earlier version of Windows.
2. If you’re running Windows 8, 8.1, or 10, you can discover event viewer by using the Windows + X key combination, which will open the WinX Menu. From the menu that displays, select Event Viewer.
Step 2 – In the Event Viewer window, select View from the toolbar > Select Show Analytic and Debug Logs from the drop-down menu.
Step 3 – You’ll then be taken to a new window with options on the left panel, from which you can choose Application and Services Logs > Microsoft > Windows > WMI-Activity.
Step 4 – Next, double-click on the WMI Activity option to expand its contents, and then choose the Operational list from the drop-down menu.
Step 5 – Next, look for any errors, and if you find one, click on it to see the error’s details at the bottom of the window.
Step 6 – In the specs window, go to the General tab and look for the ClientProcessId phrase. Write down the number.
Step 7 – Exit Event Viewer and then open Task Manager by hitting the Windows + R key combination, typing taskmgr, and then clicking OK.
Step 8 – Select “Services Tab” in the task manager window and look for any other services with the same Process ID (PID) as the ClientProcessID keyword.
Step 9 – As soon as you’ve identified the malfunctioning service, disable it right away.
Step 10 – Following that, Uninstall the defective service from Control Panel >Programs & Features.
Conclusion
So, if you’re experiencing WMI Provider Host High CPU Error while working on your computer, these are some of the greatest and most commonly used solutions. Remember to follow the steps in the article carefully and in the order that they are listed.